精品多毛少妇人妻AV免费久久,无码任你躁久久久久久老妇,欧洲av无码放荡人妇网站,女高潮大叫喷水抽搐

泰安揚帆數控科技有限公司為您提供等相關信息發布和資訊展示,敬請關注!
咨詢服務熱線:
13345281377

新聞資訊

產品

公司新聞

自動點焊機在使用中的作用

來源:http://m.meangen.com/  發布時間:2023-09-08 瀏覽次數:0

在自動點焊機的焊接過程中,普遍存在的問題是:焊點在焊接過程中不能熔透而產生飛濺,導致點焊機的焊接質量不佳,因此在實際應用中應注意:
In the welding process of automatic spot welding machines, a common problem is that the welding points cannot melt thoroughly and produce splashes, resulting in poor welding quality. Therefore, in practical applications, attention should be paid to:
一、焊接點沒有穿透,熔核沒有形成或形成不好的形成。
1、 The welding point did not penetrate, and the fusion nucleus did not form or formed poorly.
1、無滲漏,即點焊時,無“豆?fàn)?rdquo;熔核排列。這個缺陷是很危險的,它會極大地改變焊接強度。
1. No leakage, that is, during spot welding, there is no "bean shaped" arrangement of molten nuclei. This defect is very dangerous as it will greatly alter the welding strength.
2、對焊接參數進行調試。若校驗確認參數無問題,則需檢查主電源電路,如:電源是否充足,是否損壞焊接變壓器等。
2. Debug welding parameters. If the calibration confirms that the parameters are correct, it is necessary to check the main power circuit, such as whether the power supply is sufficient and whether the welding transformer is damaged.
山東數控焊接設備
二、自動點焊機數量過多。
2、 There are too many automatic spot welding machines.
1、檢查支架與機體的絕緣電阻是否不良,是否形成局部短路。
1. Check if the insulation resistance between the bracket and the body is poor and if there is a local short circuit.
2、檢查觸點表面,如銅的撓性接縫,是否被嚴重氧化,觸點電阻的形成,會加重發熱。
2. Check if the contact surface, such as the flexible joints of copper, is severely oxidized, and the formation of contact resistance can exacerbate heating.
3、檢查焊縫的厚度及負載的連續性是否符合要求,焊機是否過熱。
3. Check whether the thickness of the weld seam and the continuity of the load meet the requirements, and whether the welding machine is overheating.
4、檢查進水壓力、水量和供水溫度是否適當,系統是否被污物所隔開,這些污物會由于冷卻不佳而導致電臂過熱。
4. Check whether the inlet pressure, water volume, and water supply temperature are appropriate, and whether the system is separated by dirt, which can cause overheating of the electric arm due to poor cooling.
三、焊接時產生的意外飛濺。
3、 Unexpected spatter generated during welding.
1、檢查電流是否過大或過低的壓力。
1. Check if the current is too high or the pressure is too low.
2、焊接工件的強度不足:焊接電流越來越小,而且焊接現象也不強。
2. The strength of the welded workpiece is insufficient: the welding current is decreasing, and the welding phenomenon is also not strong.

上一篇:壓力容器自動焊機焊接接頭性能的要求有哪些?
下一篇:激光焊接機在日常延長機器壽命方法

日本a级视频在线播放| 欧美日韩亚洲国产天堂A| 精产国品一二三产品区别大吗知乎 | 久久精品亚洲中文字幕无码麻豆| 国产精品天干天干| aⅴ精品无码无卡在线观看| 国产精品亚洲А∨天堂免| 精品亚洲AV无码一区二区 | 欧美日韩亚洲国产天堂A| 无码任你躁久久久久久| 国产日产欧产精品精品蜜芽 | 国产精品免费精品自在线观看| 成人免费看吃奶视频网站| 国产成人无码a区在线观看导航| 国产av日韩a∨亚洲av电影| 久久精品动漫一区二区三区| 亚洲性猛交xxxx| 亚洲无人区码一码二码三码四码| 亚洲一区二区三区偷拍女厕| 精品久久久久久777米琪桃花| 亚洲色无码中文字幕YY51999| 亚洲高清一区二区三区电影| 粗大的内捧猛烈进出在线视频| 免费人成在线观看网站| 日文乱码一二三四| 亚洲午夜福利精品久久| 亚洲乳大丰满中文字幕| 艳z门照片无码av| 欧美疯狂做受xxxx高潮小说| 成人区人妻精品一区二区不卡| 亚洲日韩国产欧美一区二区三区| 伊人精品成人久久综合97| 欧美另类videosbestsex日本| 亚洲国产精品一区第二页| A在线亚洲男人的天堂| 中文字幕丝袜精品久久| 中国人妻被两个老外三p| 无码乱肉视频免费大全合集| 久久精品女人天堂av免费观看| 狠狠色噜噜狠狠狠狠97俺也去| 韩国三级中文字幕HD|